ATV61HC22N4 SCHNEIDER ELECTRIC DRIVE

Range of product Altivar 61 Product or component type Variable speed drive Product specific application Pumping and ventilation machine Component name ATV61 Motor power kW 200 kW
3 phases at 380...480 V 220 kW
3 phases at 380...480 V Motor power hp 300 hp
3 phases at 380...480 V 350 hp
3 phases at 380...480 V power supply voltage 380...480 V - 15...10 % supply number of phases 3 phases Line current 331 A for 480 V 3 phases 200 kW / 300 hp 357 A for 380 V 3 phases 200 kW / 300 hp 383 A for 480 V 3 phases 220 kW / 350 hp 396 A for 380 V 3 phases 220 kW / 350 hp EMC filter Level 3 EMC filter Assembly style With heat sink Apparent power 235 kVA at 380 V 3 phases 200 kW / 300 hp 260.6 kVA at 380 V 3 phases 220 kW / 350 hp maximum prospective line Isc 50 kA for 3 phases Maximum transient current 512.4 A for 60 s
3 phases Nominal switching frequency 2.5 kHz Switching frequency 2...8 kHz adjustable 2.5...8 kHz with derating factor asynchronous motor control Voltage/frequency ratio
2 points Flux vector control without sensor
standard Voltage/frequency ratio - Energy Saving
quadratic U/f Voltage/frequency ratio
5 points Synchronous motor control profile Vector control without sensor
standard Communication port protocol CANopen Modbus Type of polarization No impedance for Modbus Option card Communication card for APOGEE FLN Communication card for BACnet Communication card for CC-Link Controller inside programmable card Communication card for DeviceNet Communication card for EtherNet/IP Communication card for Fipio I/O extension card Communication card for Interbus-S Communication card for LonWorks Communication card for METASYS N2 Communication card for Modbus Plus Communication card for Modbus TCP Communication card for Modbus/Uni-Telway Multi-pump card Communication card for Profibus DP Communication card for Profibus DP V1 Complementary Product destination Asynchronous motors Synchronous motors power supply voltage limits 323…528 V power supply frequency 50...60 Hz - 5...5 % power supply frequency limits 47.5...63 Hz Continuous output current 427 A at 2.5 kHz
380 V - 3 phases 427 A at 2.5 kHz
460 V - 3 phases Output frequency 0.1…500 Hz Speed range 1…100 in open-loop mode
without speed feedback Speed accuracy +/- 10 % of nominal slip 0.2 Tn to Tn without speed feedback Torque accuracy +/- 15 % in open-loop mode
without speed feedback Transient overtorque 130 % of nominal motor torque +/- 10 % for 60 s Braking torque <= 125 % with braking resistor 30 % without braking resistor Regulation loop Frequency PI regulator Motor slip compensation Automatic whatever the load Can be suppressed Not available in voltage/frequency ratio (2 or 5 points) Adjustable diagnostic 1 LED (red) for drive voltage Output voltage <= power supply voltage electrical isolation Between power and control terminals type of cable for mounting in an enclosure With an IP21 or an IP31 kit	3 wire(s)IEC cable at 40 °C
copper 70 °C / PVC With UL Type 1 kit	3 wire(s)UL 508 cable at 40 °C
copper 75 °C / PVC Without mounting kit	1 wire(s)IEC cable at 45 °C
copper 70 °C / PVC Without mounting kit	1 wire(s)IEC cable at 45 °C
copper 90 °C / XLPE/EPR Electrical connection Terminal 2.5 mm² / AWG 14 (AI1-/AI1+
AI2
AO1
R1A
R1B
R1C
R2A
R2B
LI1...LI6
PWR) Terminal 120 mm² / 250 kcmil (PA
PB) Terminal 2 x 150 mm² / 2 x 350 kcmil (L1/R
L2/S
L3/T
U/T1
V/T2
W/T3) Terminal 2 x 150 mm² / 2 x 350 kcmil (PC/-
PO
PA/+) Tightening torque 0.6 N.m (AI1-/AI1+
AI2
AO1
R1A
R1B
R1C
R2A
R2B
LI1...LI6
PWR) 41 N.m
360 lb.in (PC/-
PO
PA/+) 24 N.m
212 lb.in (PA
PB) 41 N.m
360 lb.in (L1/R
L2/S
L3/T
U/T1
V/T2
W/T3) Supply Internal supply for reference potentiometer (1 to 10 kOhm)	10.5 V DC
+/- 5 %
<10 mA with overload and short-circuit protection Internal supply	24 V DC (21…27 V)
<200 mA with overload and short-circuit protection External supply	24 V DC (19…30 V) Analogue input number 2 Analogue input type AI1-/Al1+ bipolar differential voltage
resolution 11 bits + sign AI2 software-configurable current	0...20 mA
impedance	242 Ohm
resolution 11 bits AI2 software-configurable voltage	0...10 V DC 24 V max
impedance	30000 Ohm
resolution 11 bits sampling time 2 ms +/- 0.5 ms (AI1-/Al1+) - analog input 2 ms +/- 0.5 ms (Al2) - analog input 2 ms +/- 0.5 ms (AO1) - analog output 2 ms +/- 0.5 ms (LI1...LI5) - discrete input 2 ms +/- 0.5 ms (LI6)if configured as logic input - discrete input absolute accuracy precision +/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C +/- 0.6 % (AI2) for a temperature variation 60 °C +/- 1 % (AO1) for a temperature variation 60 °C Linearity error +/- 0.15 % of maximum value (AI1-/Al1+) +/- 0.15 % of maximum value (AI2) +/- 0.2 % (AO1) Analogue output number 1 Analogue output type AO1 software-configurable current
analogue output range 0...20 mA
impedance	500 Ohm
resolution 10 bits AO1 software-configurable voltage
analogue output range 0...10 V DC
impedance	470 Ohm
resolution 10 bits AO1 software-configurable logic output 10 V
20 mA Discrete output number 2 Discrete output type Configurable relay logic	(R1A
R1B
R1C) NO/NC - 100000 cycles Configurable relay logic	(R2A
R2B) NO - 100000 cycles maximum response time <= 100 ms in STO (Safe Torque Off) R1A
R1B
R1C <= 7 ms
tolerance +/- 0.5 ms R2A
R2B <= 7 ms
tolerance +/- 0.5 ms Minimum switching current 3 mA at 24 V DC for configurable relay logic Maximum switching current R1
R2	2 A at 250 V AC inductive load
cos phi = 0.4 and L/R = 7 ms R1
R2	2 A at 30 V DC inductive load
cos phi = 0.4 and L/R = 7 ms R1
R2	5 A at 250 V AC resistive load
cos phi = 1 and L/R = 0 ms R1
R2	5 A at 30 V DC resistive load
cos phi = 1 and L/R = 0 ms Discrete input number 7 Discrete input type Programmable (LI1...LI5)24 V DC (<= 30 V)
with level 1 PLC - 3500 Ohm Switch-configurable (LI6)24 V DC (<= 30 V)
with level 1 PLC - 3500 Ohm Switch-configurable PTC probe (LI6)0…6 probes - 1500 Ohm Safety input (PWR)24 V DC (<= 30 V) - 1500 Ohm Discrete input logic Negative logic (sink) (LI1...LI5)
> 16 V (state 0)
< 10 V (state 1) Positive logic (source) (LI1...LI5)
< 5 V (state 0)
> 11 V (state 1) Negative logic (sink) (LI6)if configured as logic input
> 16 V (state 0)
< 10 V (state 1) Positive logic (source) (LI6)if configured as logic input
< 5 V (state 0)
> 11 V (state 1) Acceleration and deceleration ramps Automatic adaptation of ramp if braking capacity exceeded
by using resistor S
U or customized Linear adjustable separately from 0.01 to 9000 s Braking to standstill By DC injection Protection type Against exceeding limit speed	drive Against input phase loss
9600 bps
19200 bps
38.4 Kbps for Modbus on terminal 9600 bps
19200 bps for Modbus on front face 20 kbps
50 kbps
125 kbps
250 kbps
500 kbps
1 Mbps for CANopen Data format 8 bits
1 stop
even parity for Modbus on front face 8 bits
odd even or no configurable parity for Modbus on terminal Number of addresses 1…127 for CANopen 1…247 for Modbus Method of access Slave CANopen Marking CE Operating position Vertical +/- 10 degree Net weight 110 kg Width 440 mm Height 1190 mm Depth 377 mm Environment Noise level 66 dB conforming to 86/188/EEC Dielectric strength 3535 V DC between earth and power terminals 5092 V DC between control and power terminals Electromagnetic compatibility Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6 Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3 Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 Standards EN/IEC 61800-3 IEC 60721-3-3 class 3C2 EN 61800-3 environments 2 category C3 EN 55011 class A group 2 EN 61800-3 environments 1 category C3 UL Type 1 EN/IEC 61800-5-1 Product certifications GOST CSA UL NOM 117 C-Tick DNV Pollution degree 3 conforming to EN/IEC 61800-5-1 3 conforming to UL 840 degree of proctection IP41 on upper part conforming to EN/IEC 60529 IP41 on upper part conforming to EN/IEC 61800-5-1 IP54 on lower part conforming to EN/IEC 60529 IP54 on lower part conforming to EN/IEC 61800-5-1 IP00 conforming to EN/IEC 60529 IP00 conforming to EN/IEC 61800-5-1 IP30 on side parts conforming to EN/IEC 60529 IP30 on side parts conforming to EN/IEC 61800-5-1 IP30 on the front panel conforming to EN/IEC 60529 IP30 on the front panel conforming to EN/IEC 61800-5-1 Vibration resistance 0.6 gn (f= 10…200 Hz) conforming to EN/IEC 60068-2-6 1.5 mm peak to peak (f= 3…10 Hz) conforming to EN/IEC 60068-2-6 Shock resistance 4 gn for 11 ms conforming to EN/IEC 60068-2-27 Relative humidity 5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3 Ambient air temperature for operation -10…45 °C (without derating) 45…60 °C (with derating factor) Ambient air temperature for storage -25…70 °C Operating altitude <= 1000 m without derating 1000...3000 m with current derating 1 % per 100 m Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Height 38.5 cm Package 1 Width 128.5 cm Package 1 Length 47.6 cm Package 1 Weight 154.0 kg Unit Type of Package 2 PAL Number of Units in Package 2 1 Package 2 Height 53.5 cm Package 2 Width 128.5 cm Package 2 Length 47.6 cm Package 2 Weight 179.0 kg Contractual warranty Warranty 18 months

Login

ATV61HC22N4 SCHNEIDER ELECTRIC DRIVE

0%

0%

0%

0%

0%

Graven Automation Pvt Ltd