ATV310HU22N4E SCHNEIDER ELECTRIC

Range of product Easy Altivar 310 Product or component type Variable speed drive Product specific application Simple machine Assembly style With heat sink Device short name ATV310 Network number of phases Three phase [Us] rated supply voltage 380...460 V - 15...10 % Motor power kW 2.2 kW for heavy duty Motor power hp 3 hp for heavy duty Noise level 50 dB Complementary Quantity per set Set of 1 EMC filter Without EMC filter type of cooling Integrated fan Communication port protocol Modbus Connector type RJ45 (on front face) for Modbus Physical interface 2-wire RS 485 for Modbus Transmission frame RTU for Modbus Transmission rate 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s Number of addresses 1…247 for Modbus Communication service Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) Line current 8.8 A at 380 V (heavy duty) 7.2 A at 460 V (heavy duty) Apparent power 5.7 kVA at 460 V (heavy duty) Prospective line Isc 5 kA ( heavy duty ) Continuous output current 5.5 A heavy duty Maximum transient current 8.3 A during 60 s (heavy duty) Power dissipation in W 75.5 W
at In (heavy duty) Speed drive output frequency 0.5…400 Hz Nominal switching frequency 4 kHz Switching frequency 2...12 kHz adjustable Speed range 1…20 for asynchronous motor Transient overtorque 170…200 % of nominal motor torque depending on drive rating and type of motor Braking torque Up to 150 % of nominal motor torque with braking resistor Up to 70 % of nominal motor torque without braking resistor Asynchronous motor control profile Voltage/frequency ratio (V/f) Voltage/frequency ratio - Energy Saving
quadratic U/f Sensorless vector control (SVC) Motor slip compensation Adjustable Output voltage 380...460 V three phase Electrical connection Terminal
clamping capacity	1.5...2.5 mm²
AWG 16...AWG 14 (L1
L2
L3
PA/+
PB
U
V
W) Tightening torque 0.8…1 N.m Insulation Electrical between power and control Supply Internal supply for reference potentiometer	5 V (4.75…5.25 V)DC
<10 mA with overload and short-circuit protection Internal supply for logic inputs	24 V (20.4…28.8 V)DC
<100 mA with overload and short-circuit protection Analogue input number 1 Analogue input type Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm Discrete input number 4 Discrete input type Programmable LI1...LI4 24 V 18...30 V Discrete input logic Negative logic (sink)
> 16 V (state 0)
< 10 V (state 1)
input impedance 3.5 kOhm Positive logic (source)
0...< 5 V (state 0)
> 11 V (state 1) Sampling duration 10 ms for analogue input 20 ms
tolerance +/- 1 ms for logic input Linearity error +/- 0.3 % of maximum value for analogue input Analogue output number 1 Analogue output type AO1 software-configurable voltage	0...10 V AC 0...10 V 0…0.02 A
impedance	470 Ohm
resolution 8 bits AO1 software-configurable current	0...20 mA
impedance	800 Ohm
resolution 8 bits Discrete output number 2 Discrete output type Logic output LO+
LO- Protected relay output R1A
R1B
R1C 1 C/O Minimum switching current 5 mA at 24 V DC for logic relay Maximum switching current 2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay 4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay Acceleration and deceleration ramps Linear from 0...999.9 s S U Braking to standstill By DC injection
<30 s Protection type Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t Frequency resolution Analog input	converter A/D
10 bits Display unit	0.1 Hz Time constant 20 ms +/- 1 ms for reference change Operating position Vertical +/- 10 degree Height 143 mm Width 105 mm Depth 151 mm Product weight 1.1 kg Supply frequency 50/60 Hz +/- 5 % Product destination Asynchronous motors Environment Electromagnetic compatibility Electrical fast transient/burst immunity test - test level

This Easy Altivar 310 drive is a frequency inverter for three-phase asynchronous motors. Its protection index is IP20. It works at a rated power up to 2.2kW/3HP, and a rated voltage from 380V to 460V AC. Its compact size, robust design and ease of installation, based on the principle of plug and play and its integrated functions make it particularly suitable for applications involving industrial machines and certain consumer machines. It offers high readability of key parameters thanks to a bright LED 4-digit display. Underload and overload detection help to protect your installation. It weighs 1.1kg and its dimensions are, 105mm wide, 143mm high, 151mm deep. This drive incorporates functions that are suitable for the most common applications, including textile machine, machine tools, wood making machine, material handling, packaging and printing machines, ceramic machine.

Login

ATV310HU22N4E SCHNEIDER ELECTRIC

0%

0%

0%

0%

0%

Graven Automation Pvt Ltd