ATS48D32Q Schneider Electric Altistart 48 SOFT starter

Range of product Altistart 48 Product or component type Soft starter Product destination Asynchronous motors Product specific application Heavy duty industry and pumps Device short name ATS48 Utilisation category AC-53A Ue power supply voltage 230...415 V - 15...10 % power supply frequency 50...60 Hz - 5...5 % Motor power kW 7.5 kW at 230 V connection in the motor supply line for standard applications 9 kW at 230 V connection to the motor delta terminals for severe applications 11 kW at 400 V connection in the motor supply line for severe applications 15 kW at 230 V connection to the motor delta terminals for standard applications 15 kW at 400 V connection in the motor supply line for standard applications 18.5 kW at 400 V connection to the motor delta terminals for severe applications 22 kW at 400 V connection to the motor delta terminals for standard applications 5.5 kW at 230 V connection in the motor supply line for severe applications Complementary Device connection In the motor supply line To the motor delta terminals Protection type Phase failure	line Thermal protection
750 Ohm at 25 °C (Stop
Run
LI3
LI4) logic
<= 8 mA 4300 Ohm Discrete input logic Positive logic Stop
Run
LI3
LI4 at State 0	< 5 V and <= 2 mA at State 1
>= 5 mA Minimum switching current 10 mA at 6 V DC for relay outputs Discrete output number 2 Discrete output type (LO1) logic output 0 V common configurable (LO2) logic output 0 V common configurable (R1) relay outputs fault relay NO (R2) relay outputs end of starting relay NO (R3) relay outputs motor powered NO Analogue output type Current output AO	0-20 mA or 4-20 mA
impedance <500 Ohm Communication port protocol Modbus Connector type 1 RJ45 Communication data link Serial Physical interface RS485 multidrop Transmission rate 4800
9600 or 19200 bps Function available External bypass (optional) Operating position Vertical +/- 10 degree Height 275 mm Width 160 mm Depth 190 mm Net weight 4.9 kg Environment Electromagnetic compatibility Conducted and radiated emissions level A conforming to IEC 60947-4-2 Conducted and radiated emissions level B conforming to IEC 60947-4-2 Damped oscillating waves level 3 conforming to IEC 61000-4-12 Electrostatic discharge level 3 conforming to IEC 61000-4-2 Immunity to electrical transients level 4 conforming to IEC 61000-4-4 Immunity to radiated radio-electrical interference level 3 conforming to IEC 61000-4-3 Voltage/current impulse level 3 conforming to IEC 61000-4-5 Relative humidity 0…95 % without condensation or dripping water conforming to IEC 60068-2-3 Ambient air temperature for operation 40…60 °C (with current derating of 2 % per °C) -10…40 °C (without derating) Ambient air temperature for storage -25…70 °C Operating altitude <= 1000 m without derating > 1000...2000 m with current derating of 2.2 % per additional 100 m Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Height 28.500 cm Package 1 Width 26.000 cm Package 1 Length 37.000 cm Package 1 Weight 5.777 kg Unit Type of Package 2 P06 Number of Units in Package 2 8 Package 2 Height 75.000 cm Package 2 Width 60.000 cm Package 2 Length 80.000 cm Package 2 Weight 58.768 kg Contractual warranty Warranty 18 months

This Altistart 48 soft start/soft stop unit is a controller with 6 thyristors used for torque-controlled soft starting and stopping of three-phase asynchronous motors. It offers soft starting and deceleration functions along with machine and motor protection functions, as well as functions for communicating with control systems. It works at a rated supply voltage from 230V to 415V AC and up to 32A rating. Altistart 48 torque control enables starting without mechanical stress and smooth control of hydraulic transitions, with a single acceleration ramp making adjustments is quick and easy, whatever the load. If connected in the motor supply line it is suitable for motors with power rating up to 15kW (at 400V) for standards applications and 11kW (at 400V) for severe applications. If connected to the motor delta terminals it is suitable for motors with power rating up to 22kW (at 400V) for standards applications and 18.5kW (at 400V) for severe applications. It weighs 4.9kg and its dimensions are, 160mm wide, 275mm high, 190mm deep. It is designed for use in the most common applications for centrifugal machines, pumps, fans, compressors and conveyors, which are primarily to be found in the construction, food and beverage and chemical industries. It complies with IEC/EN 60947-4-2 standard and is certified CE, UL, CSA, DNV, C-Tick, GOST, CCC, NOM, SEPRO, and TCF. The Altistart 48 is connected directly to the Modbus bus via its RJ45 connector port, It can also be connected to Ethernet, Fipio, Profibus DP and DeviceNet networks via a module (bridge or gateway) to order separately. It is designed to be mounted in vertical position (+/- 10 °) on a panel, thanks to 4 fixing holes. Altistart 48 delivers high performance with its Torque Control System (TCS) for controlled starting and deceleration, an easy integration in enclosures and control systems. This range provides also continual improvement of your machine operation by reducing mechanical or hydraulic stress and limiting energy loss and temperature rise, plus more.

Login

ATS48D32Q Schneider Electric Altistart 48 SOFT starter

0%

0%

0%

0%

0%

Graven Automation Pvt Ltd